BEHLEN STAIN-N-TONE
Lacquer Brush or Spray Stain & Spray Toner
STAIN-N-TONE
Lacquer Brush or Spray Stain
& Lacquer Spray Toner

Available Colors
B510-384 .... Oak, Golden
B510-386 .... White
B510-387 .... Black
B510-388 .... Cordovan Mahogany
B510-389 .... Van Dyke Brown (Dark Cold Brown)
B510-390 .... Oak, Dark
B510-391 .... Walnut, Medium Brown
B510-393 .... Fruitwood / Teak / Lt Walnut
B510-394 .... Maple, Colonial
B510-396 .... Mahogany, / Cherry
B510-397 .... Dark Walnut
B510-398 .... Oak, Light

Features:
Stain-N-Tone colors are solvent based pigmented stains. Stain-N-Tone can be used as a stain by applying directly to bare wood, or it can be added to nitrocellulose lacquer to make a toner.

Physical Properties:
Weight Solids: ... Ranges from 7.5% to 10.3%
Volume Solids: ...Ranges from 3.6% to 4.1%
Dry Time: ...Air dry to seal or top coat in 20-30 minutes at 77 deg. F & 45% relative humidity with good air movement.
Spread Rate: ... Ranges from 57-66 sq. ft/ gal.
at 100% efficiency
Weight Per Gallon: ...7.07 lbs./ gal average
VHAPS: ... No greater than 0.42 lbs HAPs/ lb. solids
VOC: ... average 6.48 lbs./ gal.
Flash Point: ... -4 deg. F., TCC

Reducer:
42.101 Lacquer Reducer

Application Equipment:
May be applied by spraying or brushing.

Finish Systems
Wood Preparation. Finish sand with 120-180 grit sandpaper. Wood should be dust free with a moisture content between 6-8 %.

Directions for Use
Mix Stain-N-Tone thoroughly making sure all pigment is off the bottom of the can. Spray or brush Stain-N-Tone on bare wood. Wipe off excess immediately to achieve desired color and effect.
Air dry 20-30 minutes then proceed with sealer and lacquer. Stain-N-Tone can be added to Lacquer or sealer to increase color strength or shade.
Add no more than 25% by volume and spray already stained wood.
Use Lacquer Reducer/Thinner to clean equipment.

 Safety and Storage Precautions
CONTAINS:
ESTERS, ALCOHOL, KETONE AND PETROLEUM DISTILLATES. NON-PHOTOCHEMICALLY REACTIVE -- VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION.

NOTICE:
Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
Use only with adequate ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness, or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH/MSHA Approved) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Do not get in eyes, on skin or on clothing. Wash thoroughly after handling.

Vapors may ignite explosively.
Keep away from heat, sparks and flame.
VAPORS MAY CAUSE FLASH FIRE.
Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation.

First Aid
If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately flush eyes or skin with plenty of water for at least
15 minutes. Remove contaminated clothing and shoes. If swallowed, so not induce vomiting.
Call physician immediately, If spilled, contain
spilled material and remove with inert absorbent.
Dispose of contaminated absorbent container and unused contents in accordance with local, state, and federal regulations.

KEEP OUT OF REACH OF CHILDREN.
Consult MSDS for more information.

For industrial use only. For shop use only.


Wood Finish Supply